• Sockets (on/off)
• Lamps (on/off)
• Contact Sensors
• Blinds
• Smoke Detectors
• Blinds (inverted)
• Lamps (dimmer)
• Motion Sensors
• Push Switches
• Lock Contact
• Blinds (%)
• Blinds (& inverted)
• Push Buttons (selectors)
• Lock Mechanisms
• Lock Mechanisms (inverted)
• Temperature sensors (only temperature characteristic in case of T+H / T+H+B)
• Thermostat SetPoints

• General kWh power meters - Types: General, Current; SubType: kWh, mapped to Eve chars where possible
• General Current, Voltage - Types: General, SubType: Current,Voltage, mapped to Eve chars where possible
• CurrentCost USB power meter - Type: Usage, SubType: Electric, mapped to Eve chars where possible
• P1 Smart Meter (Electric & Gas), mapped to Eve chars where possible
• EvoHome** / OpenTherm Thermostat support - Types: Heating, Thermostat; SubTypes: Zone, SetPoint
• YouLess Meter (Current, Total and Today Total Consumption) - Type: YouLess Meter; SubType: YouLess counter, mapped to Eve chars where possible
• General Usage % meters (eg: Motherboard Sensors Hardware Device - CPU %, Mem %, HDD % etc) - Type: General; SubType: Percentage
• Temperature, Temp + Humidity, Temp + Humidity + Baro (Current Temperature, Current Humidity, Current Pressure in hPA) - Type: Temp, Temp + Humidty, Temp + Humidity + Baro [id'd as Eve Weather]
• DarkSkies Virtual Weather Station Sensors (Wind, Solar Radiation, Rainfall, Visibility, Barometer [id'd as Eve Weather])

** assumes the EvoHome has been setup according to this script method.

~/.homebridge/config.json example:

{
    "bridge": {
        "name": "Homebridge",
        "username": "CC:21:3E:E4:DE:33",
        "port": 51826,
        "pin": "031-45-154"
    },
    "platforms": [
        {
            "platform": "eDomoticz",
            "name": "Domoticz",
            "server": "127.0.0.1",
            "port": "8080",
            "ssl": false,
            "roomid": 0,
            "mqtt": true,
            "debuglog":false,
            "excludedDevices": [],
            "dimFix": 0
        }
    ],
    "accessories": []
}

To prevent certain Domoticz devices from showing up in HomeBridge it is possible to exclude them by setting the "excludedDevices" parameter. Provide an array of Domoticz Device IDX's, which can be found in the Domoticz dashboard on the "Setup > Devices" page and look for the "idx" column.

"excludedDevices": ["12","30","129"]

The dimFix variable relates to an early issue between HomeKit and Domoticz regarding scaling of dimmer values. These days, for the majority of setups this variable can be set to 0 or omitted entirely. If you find that you can never set your dimmers to 100%, then set this variable to 1. If you find that, when you set your dimmers, this starts a never ending loop of brightness increasing by 1%, then you MUST omit this variable or set it to 0.

"dimFix": 0

MQTT

By default, the plugin will grab hardware information regarding MQTT from Domoticz if mqtt is 1 or true in the configuration file. Advanced users can override their MQTT configuration as follows:

"mqtt": {
  "host": "alternate.mqtt.com",
  "port": 1234,
  "topic": "domoticz/out",
  "username": "username",
  "password": "password"
}

Values can be omitted from this dictionary, and the values that need overriding can be kept, e.g.

"mqtt": {
    "port": 1234
}

to only override the port value.

SSL

Set "ssl":1 or true in config.json to turn on SSL (ie: server connects with https:// rather than http://). You will need to specify your SSL port - usually "port":"443" by default.