Before any update save configuration, reset to factory default and reload configuration. EEPROM can change without any further advice.

PedalinoMini™

Wireless MIDI foot controller for guitarists and more.

• Plug-and-play with any MIDI-compatible app on iOS 8 and above as well as OS X Yosemite and above.
• High customizable using web interface
• Bluetooth, WiFI, USB and legacy MIDI interfaces
• No extra drivers to connect Windows, macOS, iOS (iPad/iPhone) and Android
• Bluetooth LE MIDI (iOS and macOS compatible)
• Network MIDI (aka AppleMIDI or RTP-MIDI)
• ipMIDI
• Open Sound Control (OSC)
• IEEE 802.11 b/g/n Wi-Fi 2.4 GHZ with WPA/WPA2 authentication
• Bluetooth Low Energy 4.0
• DIN MIDI IN and MIDI OUT connectors
• MIDI routing
• MIDI clock master and slave
• MIDI Time Code (MTC) master and slave
• OSC to MIDI and vicecersa
• Any number of pedals of any type in any order
• Auto-sensing footswitches and expression pedals

Features

• Support for digital foot switches (momentary or latch), analog expression pedals and jog wheels (rotary encoders)
• 6 controllers ports. One controller port can support up to 6 indipendent switches for a total of 36 switches.
• 20 banks
• 3 user profiles
• 16 sequences of 10 steps each
• Each port can connect 1 expression pedal or 1 jog wheel or up to 6 foot switches via a resitors ladder (TC HELICON Switch-6).
• MIDI output via AppleMIDI (also known as RTP-MIDI) or ipMIDI via Wi-Fi
• Send almost every MIDI messages: Program Change, Control Code, Note On/Off, Channel Pressure, Pitch Bend, Bank Select, Start, Stop, Continue or a sequence of the previous messages
• MIDI channel, MIDI note, MIDI control code, MIDI program change can be configured by each pedal and by each bank
• Switch debouncing and analog noise suppression without decreasing responsivenes
• Invert polarity via software
• Individual automatic calibration of expression pedals. Manual fine tuning is not usually requested.
• Transform a linear expression pedal into log expression pedal and vice versa
• Resistors ladder calibrated is easy as pressing footswitches in sequence
• RGB NeoPixel/WS2812B status leds
• Responsive and mobile-first configuration web interface (http://pedalino.local)
• Smart Config technology to help users connect to a Wi-Fi network through simple app on a smartphone.
• OTA (Over the Air) firmware update or via HTTP (http://pedalino.local/update)

Bill of materials

The shortest bill of materials ever: an ESP32 board and a OLED display. That's it.

• Any ESP32 board supported by Arduino core for ESP32 WiFi chip
  • Tested on DOIT ESP32 DevKit V1 4M dual-mode Wi-Fi and Bluetooth module
• OLED I2C 0.96"/1.3" display 128x64 pixels SSD1306/SH1106 based

Not enough short?

• An all-in-one TTGO T-Eight ESP32 with a bigger OLED display (1.3"), 4MB PSRAM and onboard lithium battery interface

• An all-in-one Heltec WiFi Kit 32 with an integrated OLED display (0.96") and onboard lithium battery interface

• The new TTGO T-Display with an 1.14" IPS display and onboard lithium battery interface

USB MIDI and DIN MIDI connection requires additional hardware.

Schematic

Do not forget the add the pull-up resistors on PIN_A1 to PIN_A6 otherwise pins will be floating. A floating pin can trigger unexpected MIDI events. As alternative you can disable the not used pedals via web interface.

How to build and upload

PlatformIO is the recommended IDE for PedalinoMini™ build and upload.

1. Install PlatformIO IDE for VSCode
2. Install Git
   • On Windows, install git from https://git-scm.com/download/win
   • On macOS, install Command Line Tools for Xcode running xcode-select --install via Terminal
3. In VSCode run the following commands:
   • from View->Command Palette (Ctrl+Shift+P)
     • Git: Clone
     • You will be asked for the URL of the remote repository (https://github.com/alf45tar/PedalinoMini) and the parent directory under which to put the local repository.
   • under PlatformIO Project Tasks select your environment (i.e. env:esp32doit-devkit-v1)
     • Click "Build" under General
     • Click "Upload" under General
     • Click “Upload File System Image” under Platform. Do not skip this step otherwise the WebUI will not works properly.

That's all folks.

USB MIDI

The cheapest and compact way to implement an USB MIDI connection is using an Arduino Pro Micro and the BlokasLabs/USBMIDI library. Upload the UsbMidiConverter example into the Arduino Pro Micro.

Serial1 of ESP32 (re-mapped to pin 18 RX and 19 TX) is connected to Serial1 (pin 1 TX0 and pin 2 RX1) of Arduino Pro Micro. Use a 3.3V Pro Micro board. A 5V Pro Micro board works too because the ESP32 is usually 5V tolerant.

Arduino Pro Micro is powered by the USB MIDI connection.

IMPORTANT: ESP32 board and Arduino Pro Micro must share GND.

Booting modes

PedalinoMini™ has 8 booting modes:

The last booting mode (1-5) is selected if you don't press any button on boot.

The default boot mode is (1) Normal.

To select a different mode:

• Press and release EN button (POWER button on TTGO T-Eight) and immediately after press and hold BOOT button (CENTER button on TTGO T-Eight)
• Follow the istructions on display. Keep it pressed until the progress bar reach the end to reset to factory default. If you release the button before the progress bar reach the end PedalinoMini™ will start in one of the supported boot mode.

• (x) Supported (-) Not supported
• USB-MIDI and DIN-MIDI are always available if hardware implemented.

How to connect PedalinoMini™ to a WiFi network

PedalinoMini™ supports IEEE 802.11 b/g/n WiFi with WPA/WPA2 authentication (only 2.4 GHz).

PedalinoMini™ implements Wi-Fi Protected Setup (WPS) and Smart Config technology (Espressif’s ESP-TOUCH protocol). WPS needs access to the WPS button on the WiFi router. Smart Config requires a smartphone with one the following apps:

• ESP8266 SmartConfig for Android
• Espressif Esptouch for iOS

If the WiFi network is not available PedalinoMini™ will create an hotspot for you. Once connected to the PedalinoMini™ hotspot, you can use the web interface to set the SSID and password of an access point that you would like to connect to.

• On power on PedalinoMini™ will try to connect to the last know access point
• If it cannot connect to the last used access point within 15 seconds it enters into Smart Config mode
• Start one of the suggested apps to configure SSID and password
• If it doesn't receive any SSID and password during the next 15 seconds it enters into WPS mode
• Press or press and hold (it depends by your router) the WPS button on your WiFi router after PedalinoMini™ entered in WPS mode
• If it doesn't receive any SSID and password during the next 30 seconds it switch to AP mode
• In AP mode PedalinoMini™ create a WiFi network called 'Pedalino-XXXXXXXX' waiting connection from clients. The required password is XXXXXXXX (uppercase). XXXXXXXX is a variable string.
• Reboot PedalinoMini™ to restart the procedure.

void wifi_connect()
{
  auto_reconnect();           // WIFI_CONNECT_TIMEOUT seconds to reconnect to last used access point
  if (!WiFi.isConnected())
    smart_config();           // SMART_CONFIG_TIMEOUT seconds to receive SmartConfig parameters and connect
  if (!WiFi.isConnected())
    wps_config();             // WPS_TIMEOUT seconds to receive WPS parameters and connect
  if (!WiFi.isConnected())
    ap_mode_start();          // switch to AP mode until next reboot
}

How to connect to the web user intertace

The responsive and mobile-first configuration web user interface is available on http://device-name.local address (the address is case insensitive). The device identification name is unique per device. Every device/board has a different device name. For example I am using http://2ab267ac.local to connect to my PedalinoMini™.

In order to know your device name and/or the IP address press for at least half a second the BOOT button and check the display.

As alternative method you can use the IP address. If you are using the AP mode the IP address is always 192.168.4.1 and the connection address is http://192.168.4.1 for everyone.

The default username and password to connect to web user interface are admin as username and your device-name in uppercase as password. For example I am using admin as username and 2AB267AC as password.

Device name, username and password can be changed via web user interface in the Options page.

Pedals

Once PedalinoMini™ is connected to a WiFI network and you are connected to the web user interface it is time to configure which pedal/controller is connected to each of the 6 available ports. Pedal 7 and 8 (if present) are the on board buttons and they are fully configurable.

Actions

Once Pedals setup is complete proceed with Actions setup to define which event (press, release, double press, long press, move or jog) trigger an action.

1. Select a bank on top left
2. Select a pedal on top right or "All"
3. (Optional) Enter the Bank Name
4. Click on New Action and select a pedal on the dropdown menu. The pedal number of an action cannot be changed anymore without delete and recreate the action.

• (-) Not used
• (+) if velocity is not zero it is equivalent to NOTE ON
• MSB is the Most Significat Byte. It is a fixed value from 0 to 127.
• LSB is the Less Significat Byte. It is the variable value from 0 to 127.

Interfaces

The supported interfaces are:

For each interface there are 4 filtering options:

Routing between different interfaces is enabled between every IN enabled interfaces to any OUT enabled interfaces. Do not confuse routing (different interfaces) with MIDI Thru (between IN and OUT of same interface).

Sequences

Options

PedalinoMini™ has a lot of options well documented in the Options page.

Configurations

The complete profile setup can be saved as configuration to be used later or just for backup reason in case of hardware failure. Configuration files can be downloaded and shared with others PedalinoMini™ users.

Some example configurations are provides. More to come.

iRig BlueBoard

PedalinoMini™ can emulate an IK Multimedia iRig Blueboard using 'blueboard' configuration. Midi Mode 1 is on bank 1 and Midi Mode 2 is on bank 2. PedalinoMini™ emulation works on any MIDI interface and not only "MIDI over Bluetooth" as the original iRig Blueboard.

Fender Mustang Amplifier

PedalinoMini™ can control a Fender Mustang I/II/III/IV Amplifier via MIDI. Additional software is required to translate MIDI messages to the proprietary USB protocol used by Fender Mustang amplifiers. The bonus configuration is called 'mustang2' and works with 3 momentary switches and 3 jog wheels.

Display mode

Where	What	Display	Description
Bank Name	Empty		If the current bank name is empty the current profile and the current bank is shown using a vintage 7 segment LED style. First digit is the profile, the others two are for bank.
Bank Name	Any		If current bank name is not empty the bank name is displayed within the 6 pedal names. PedalinoMini™ assumes the first action tag for the pedal as its pedal name. The bank name screen will switch every 4 seconds to display pedals current value if no event occurs.
Bank Name	:		If the bank name start with colon (:) the bank name is always shown (if no event occurs).
Bank Name	.		If bank name start with point (.) the current values are shown and events update values in real time without any display switch.
Action Tags	:		If action tag start with colon (:) the display is not switched when an event occurs.
Action Tags	.		If action tag end with dot (.) the corresponding led and color is set on boot.
Action Tag	###		A triple hashtag sign (###) in action tag is replaced with the current value of the parameter.

How to switch profiles

During normal operation

• Single press of BOOT button to move to the next profile
• Double press of BOOT button to move to the previous profile
• Long press of BOOT buttom to switch between live performance display and scrolling pages where configuration parameters (the device name, the IP address etc.) are displayed.

On TTGO T-Eight replace BOOT button with CENTER button.

Factory default configuration

The factory default configuration is quite simple: 6 momentary pedals, one actions on press, all MIDI interfaces interface enabled. More configuration are available here.

End User Built (oldest first)

https://github.com/marosell

https://github.com/mknerr

https://github.com/alf45tar

https://github.com/jimhiggs

https://github.com/raidolo

https://github.com/bsos

https://github.com/rigr

https://github.com/teopost